Brodix Small Block Chevy Compatible Block Manuel d'utilisateur télécharger pdf

www.brodix.com • 301 MAPLE AVENUE • P.O. BOX 1347 • MENA, AR 71953

ORDER, TECH, AND INFORMATION: (479) 394-1075 • FAX: (479) 394-1996

General Instructions for Small

Block Chevy Compatible Blocks

WARNING!

PLEASE CHECK THE BLOCK

THOROUGHLY IN EVERY POSSIBLE WAY.

IF YOU SUSPECT A DEFECT, CONTACT

BRODIX, INC. OR THE DEALER IT WAS

PURCHASED FROM BEFORE ANY

WORK HAS BEGUN. BRODIX® WILL NOT

BE RESPONSIBLE FOR VISIBLE DEFECTS

AFTER ANY WORK HAS BEEN STARTED.

INSPECT THE BLOCK FOR DAMAGE FROM

SHIPPING. INSPECT THE BLOCK OIL

PASSAGES AND THREADED HOLES.

WARNING!

THE SLEEVES ARE LEFT ABOVE THE DECK OF

THE BLOCK INTENTIONALLY. IT IS THE ENGINE

BUILDER’S PREFERENCE WHETHER OR NOT TO

SURFACE THE SLEEVES FLAT WITH THE DECK

OF THE BLOCK.

ALL PLUGS, LOCKS, AND SCREWS MUST HAVE

ANTI-SEIZE ON THE THREADS.

• The sleeves must be clearanced before initial

installation of crank and rods.

• The block must be align honed and checked

for bearing clearance.

• The cylinders must be ﬁ nish bored and

honed.

• You must check clearance before the

ﬁ nal installation of crank, rods, pistons,

and cam in the block.

• Wash the block thoroughly with soap

and water, and blow dry with air.

• Install the rear cam plug with the o-ring and

snap ring in place.

• Install all required water and oil plugs.

See Diagram A and B.

• Apply anti-seize to all main and head stud threads

before installation. Hand tighten only.

The BRODIX

® cam bearing, part number

8B CAM BEARING, uses three 1/4 inch allen head

cap screws to lock the center three bearings in place.

The allen head cap screws must be ﬁ tted for the

proper length. The front and the rear bearing

will use spiral locks. Roller bearings are held

into place on both sides with spiral locks.

Diagram B

(Front)

WARNING!

PLEASE BE ADVISED THAT HEAT SOAKING AN

ALUMINUM BLOCK ABOVE 250° F CAN DRASTICALLY

AFFECT THE HARDNESS.

CLEANING TECHNIQUES THAT UTILIZE HEAT ARE NOT

RECOMMENDED.

Please feel free to call or write if there are any problems

or questions.

We have a complete repair service available if block

damage occurs.

No warranties of any nature (expressed, implied, ﬁ tness of usage or merchantability) are given on these products. Seller

undertakes no responsibility for any product sold. Additional disclaimers are within and are binding upon this contract. Due

to the intended usage of products offered, all products are sold on an “as-is” basis, and no warranties of any kind, whether

written or oral are made by BRODIX, Inc., its agents or employees. All implied warranties, including the implied warranties

of merchantibility and ﬁ tness are expressly excluded, and the buyer bears the entire risk as to quality performance and use

of these products. BRODIX, Inc. will assume no responsibility of personal injury, labor or other injury arising out of the us-

age of high performance racing parts or products. Any defective part will be handled between the original manufacturer and

the buyer. BRODIX, Inc. reserves the right to change speciﬁ cations, prices and discontinue parts without notice. Installation

of BRODIX heads may adversely affect the vehicle manufacturer’s warranties, and may violate State and Federal laws when

vehicles so equipped are operated other than strictly off-highway. BRODIX reserves the right to discontinue any product at its

sole discretion and without any liability with respect to similar products already in the ﬁ eld. Some parts are not legal for sale

or use on pollution controlled motor vehicles.

IF YOU NEED TECHNICAL ASSISTANCE, CALL

(479) 394-1075

Thank You

For Buying BRODIX!

WARRANTY DISCLAIMER

WHILE OUR PRODUCTS ARE USED ON MANY SUPER-CHARGED APPLICATIONS

SUCCESSFULLY, PLEASE BE AWARE THAT THERE IS A GREATER POTENTIAL

FOR ENGINE DAMAGE DUE TO THE POSSIBILITY OF TUNING ERRORS.

PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE.

ALWAYS CONFIRM PRICE WHEN PLACING YOUR ORDER.

WE WILL MAKE EVERY EFFORT TO KEEP YOU INFORMED OF INCREASES.

www.brodix.com • 301 MAPLE AVENUE • P.O. BOX 1347 • MENA, AR 71953

ORDER, TECH, AND INFORMATION: (479) 394-1075 • FAX: (479) 394-1996

Oil Feed Location on Dry Sump

Application (1/2 Pipe Plug Required

for Wet Sump Application)

Oil Restrictor

Locations

1/4 Pipe

1/4 Pipe Plug

1/4 Cam Lock Locations

(Standard Cam Bearings Only)

Oil Filter Inlet for Wet

Sump Block (1/2 Pipe

Plug Required for Dry

Sump Application)

Oil Filter Outlet for Wet Sump Block

(1/2 Pipe Plug Required if Oil Is Fed

at Front of Block)

1 5/16 Hexed O-Ring

Water Plugs

3/8 Pipe Plug

1 5/16 Hexed O-Ring

Water Plugs

AN -6 O-Ring Plug

AN -7 O-Ring Plug

1/4 Pipe Plug

Oil Pressure

-10 O-Ring Plug for

Wet Sump Use

(Use as a Scavenge

Return for Dry Sump)

Diagram A

(Back)

BRODIX® STOCKS A

FULL LINE OF

REPLACEMENT AND

REPAIR PARTS.

1 2

Résumé du contenu

Page 1 - Thank You

www.brodix.com • 301 MAPLE AVENUE • P.O. BOX 1347 • MENA, AR 71953ORDER, TECH, AND INFORMATION: (479) 394-1075 • FAX: (479) 394-1996 Not l

Page 2 - ® block is no exception and

BLOCK PART NUMBERSMAIN CAP PART NUMBERSSLEEVES • 8B HS 3650: 3.650 X .4375 • 8B HS 4750: 4.750 X .4375 • 8B HS 5000: 5.000 X .4375 • 8B HS

Commentaires sur ces manuels

Pas de commentaire

Brodix Small Block Chevy Compatible Block Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Brodix Small Block Chevy Compatible Block. Brodix Small Block Chevy Compatible Block User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Brodix Small Block Chevy Compatible Block